Engine

All 280Z ENGINE related parts

280Z fuel pressure regulator

Used 77-78 Nissan OEM 280Z fuel pressure regulator, pn 22670-N4700 Part Fitment Model Year Trim Important vehicle option details 280ZX 07/1978--1983 GL, NON GL   L28E Datsun 810 1980-1984 DX, SL L24E - 6 Cyl 2.4L There are aftermarket replacements in the market, but none have the same design nor proper OEM factory mounting tabs that allow them to be installed securely and in proper location on a nicely restored or daily driver car. These OEM units are very scarce to find in this clean of condition any

Used 77-78 Nissan OEM 280Z fuel pressure regulator, pn 22670-N4700


62860-n4400_67461k

USED, excellent cosmetic condition, air cleaner extension for 2/76-1978 Datsun 280Z cars. May fit 1975 models? There are no cracks or breaks in this extension, all mount points are intact and accordion section soft and flexible, making this part ideal to install on a refurbish or restored 280Z .  Adds some nice vintage Z car look to cars missing one. Part has been thoroughly cleaned inside and outside making it an excellent replacement for your funky, missing or scuffed up tube. Note: Probably will attached to 280Z models sold outside USA market.  Requires a small metal clamping

Used, excellent condition Nissan OEM 280Z air cleaner extension  pn 62860-N4400


Custom Polished Air Regulator, pn 22660-N4210

Polished Air Regulator, 22660-N4210 Used, Custom Polished Air Regulator, pn 22660-N4210 (replaces 22660-N4200) for 75-78 Datsun 280Z and 79-83 280ZX models.  May also fit 80-84 Datsun 810/Maxima models. Stamped in number on body is A32-600000. This unit also referred to as IACV, Auxiliary Air Regulator and Idle Air Control Valve Alternate Nissan part numbers found that appear to be for this same unit are 22660-N4200, 22660-W2465, A32-600 003 Non polished, used & tested units also available priced at $125.00.  Contact us to purchase a used unit. Part Fitment

UsedCustom Polished Air Regulator, (pn 22660-N4210) for Datsun 75-78  280Z, 79-83 280ZX & 80-84 Datsun 810/Maxima models.


9mm rods

9mm rods for "Stroker Motor" build Much sought after and hard to find, used set of 6 special 9mm connecting rods most often used to build a Nissan L28 "Stroker Motor".  Most Nissan factory installed connecting rods were "8mm" as opposed to "9mm" rods used only in a small number of 240Z L24 engines.

Used set of hard to find, L24 engine, 9mm connecting rods most often used to build Nissan L28 “Stroker Motors”.


7364rw1k

L6 engine support insulator New, NOS RH/LH Front engine support insulator for 70-78 240Z, 260Z, 280Z and 79-83 280ZX.  May also be correct for any other Datsun models of that era that came with L4? & L6 engines installed, such as Datsun 810, Maxima.  Send us measurements of insulator you are replacing and we'll compare it to this NOS unit or check  interchange for other classic Datsun models at carpartsmanual.com

New, NOS RH/LH Front engine support insulator for 70-78 240Z, 260Z, 280Z and 79-83 280ZX


280heaterhose_lg

Water heater hose for Datsun 280Z Excellent used condition water heater hose for 75-78 Datsun 280Z models. No cracks in end rubber indicates that this hose was virtually new with very little in service tine before being removed from wrecked car.  Good deal if you've been looking for this critical NLA part for long.  Superseded Nissan pn: B7182-N4220

Excellent used condition water heater hose for 75-78 Datsun 280Z models.