Engine

Above average Used condition, Datsun/Nissan L6 engine timing cover, 13501-A8600 NOTE:  "Above average used condition" covers will have minimum water pump passage cavitation and no scratches on seal or gasket surfaces of any concern to an engine builder.  Bead blasted, cleaned up covers are not always ready to ship.  Usually we can get one ready to ship within a few days to a week if a prospective buyer alerts us to his/her needs a bit in advance.  Please call before placing an order. Fits all 70-83 L24, L26, L28 engines used original to 240Z, 260Z, 280Z and 280ZX models.  Also ot

New, OEM Power valve 16059-n3314 (F-1/R-1, third series w/green paint) for 1973/1974 Datsun 240Z/260Z models with OEM "flat top" Hitachi SU carburetors.  Last and most improved, modified design of the 3 that Nissan developed to fit 73-74 Datsun SU carburetors.  These rare to find, OEM power valves, have been NLA for many years now. Note: Price is for one power valve, not a pair, as pictured.  This NOS power valve design is one of 2 that make a matched set. pn for other one is 16059-n3313. It can still be beneficial to install just one improved power valve to an aged set of SU flat tops.

New, NOS  240Z driver side motor mount bracket  11231-E4100 Note: we usually have these in used condition at lower price.  Contact us direct for a quote.

New OEM 240Z fan belt, 11720-E8700 Nissan NOS OEM Fan Belt, pn 11710-E8700 replaced by 11920 M6600 This belt, in Nissan OEM pkg is labeled "Bando 11720-E8700  JAPAN" To insure a no hassle purchase online please compare measurements of this belt with one you intend to replace. V-Belt Width: 13 mm Length: 800 mm Belts: V type

Excellent, used condition, original "Elephant" JDM valve cover oil cap for 72-73 240Z models. Photo shows actual cap for sale. Note: We also have several more of these caps in stock for sale priced somewhat lower dependent on degree of aged, used condition.  If interested please call us direct for a quote.

NOS OEM NLA 240Z/260Z Crankshaft Harmonic Balancer Pulley part # model applied date qty interchange superceded from to newer former ASSY-PULLEY WITH DAM 12303-E4600 L24 7206 1 12303-N3300 L24 7207 7302 1 No No 12303-E4600 12303-N3302 L24,L26 7303   1  Yes  No 12303-N3300 NOTE: Before purchasing please email us a photo showing us relative position of crankshaft pin slot to timing index marks on your pulley in order to insure that this pulley/dampener will be correct for your application. In some cases we have seen

Nissan NOS head gasket for L24 engines, pn 11044-E3101 If you are over boring your engine as part of a rebuild please email us with a request to measure diameter of cylinder cut out of this gasket before purchasing to ensure that it will meet your needs NISSAN 11044-E3101 can be used in car models NISSAN DATSUN 240Z DATSUN 240 Coupe 1969-1973 1978-1981 LAUREL 1977-1983 LAUREL 1981-1985 LAUREL 1984-1990  

9mm rods for "Stroker Motor" build Much sought after and hard to find, used set of 6 special 9mm connecting rods most often used to build a Nissan L28 "Stroker Motor".  Most Nissan factory installed connecting rods were "8mm" as opposed to "9mm" rods used only in a small number of 240Z L24 engines.

L6 engine support insulator New, NOS RH/LH Front engine support insulator for 70-78 240Z, 260Z, 280Z and 79-83 280ZX.  May also be correct for any other Datsun models of that era that came with L4? & L6 engines installed, such as Datsun 810, Maxima.  Send us measurements of insulator you are replacing and we'll compare it to this NOS unit or check  interchange for other classic Datsun models at carpartsmanual.com

Cold Air RAM induction cone New Aftermarket 3" collar ,Cold Air RAM Induction Intake Cone / filter